Some Of The Common water heater problems and their solutions-Explained

common water heater problem and their solutions

Some Common water heater problems

No hot water

First, in our common water heater problem and solution guide is the most common issue that you might face with a water heater, and that is when the water doesn’t get hot anymore. There are a lot of reasons that might cause this issue to happen.

In most cases, the water is not getting hot because it’s not receiving any power; thus, there is no hot water. So, if you want to fix it, you should definitely call out an expert to help you with that. However, if you want to do it all by yourself, first cut off the power to your house and then try to do it.

For water heater installation and repair contact Rancho Cucamonga Plumber

Not hot enough

This is another huge issue that’s very commonly seen in water heaters. In this case, the engine of the heater might not be that powerful to deal with that. If that’s the case, you should definitely consider buying a new electric water heater.

 But if you don’t want to go for a replacement, it’s best to change the thermostat of the device. That should fix the issue and you are going to get water that’s hot again. So, make sure to try this method out, and it should take care of everything well.

Water Too Hot

Next up, we have another common issue that we face with a water heater on a regular basis. Water getting too hot is a very risky and quite a common problem, but it can be fixed with some easy hacks.

 In most cases, the temperature-pressure valve makes the whole thing off balance. Also, it’s extremely risky to operate using the water heater when it’s in this condition. So, make sure to get the valve fixed before you start using the water heater in the first place.

Smelly Water

Bacteria in water causes the water to smell bad eventually, which is not a good thing. To get it clear, use some chlorine bleach, and it works like magic. But if it’s too bad, you can take your time getting it cleaned thoroughly.

 Just get the tank empty at first, and then start cleaning the tank. Use any cleaning solvent that gets rid of the bacteria and problematic areas. Once it’s cleaned well, you’d have to wash everything once again with clean water. Finally, fill up the tank and empty it so that there’s no more dirt remaining inside the tank. After that, you can use the water heater normally and without any issue.

Noisy tank

If the tank is noisy when you’re using the water heater, then that’s a dead giveaway that the thing is not functioning properly. In most cases like that, you’d have to replace the whole tank. Also, you can check for any screws that are not tight, which might make noise.

 Remember, if you don’t take care of a noisy tank, it might cause more trouble in the near future. So, it’s best to deal with it when the problem is small, and it’s going to save you a lot of trouble.

Leaks

Leaks can spill the water everywhere and make a mess of your place pretty easily. Thankfully, if you can spot the leak, it should not be that difficult to fix.

 In most cases, tightening the parts will do the trick and stop the water permanently. But if that’s coming from any valve or something that you can’t tighten or apply tape on, then you must go for a replacement. But if you can’t get it fixed, don’t hesitate to hire plumbers to get it fixed.

Dirty Water

Dirty water indicates that something is wrong inside the tank, and you should take a look at it. Sometimes the water can even get smelly, and that’s another huge giveaway that the water is dirty.

 If you encounter this problem, just try to change the tank and replace it with a new tank. That’s going to get rid of the problem. You can also try attempting cleaning as well, which would take so much time. So, check if you need to go for a replacement at first, and then do what’s required.

Extra tips

If you don’t know what the issue is with your water heater, then don’t try to get things going. Just take it to a professional, and he’ll fix it for you. It’s better to spend a few dollars on the repairs rather than ruining parts while you don’t know what you’re doing.

 You’ll find a lot of services that can fix your issue within a short period, and you’ll only have to spare a few dollars to get it fixed. So, if you are not sure what to do, consider leaving it to the experts. It might save you from wasting a whole bunch of money on the damage you do try to fix everything by yourself.